| Trail Camera T-Post Mount No tree...No problem! Fits most cameras and provides 360 degree positioning at any height. |
| Camera and T-post are not included. |
Features
- All steel construction; no plastic.
- Very sturdy and durable; raccoons can swing from it, cows can "itch" on it without altering camera aim.
- Can be clamped at any height and turned left or right a full 360 degrees.
- NO glue, double sided adhesive tape or camera hole drilling involved.
- Durable Matt Black powder coat finish.
- All necessary attachment hardware is included.
General Instructions
- Cameras that come factory equipped with nylon straps, are attached using the supplied metal strap.
- Cameras designed to be fastened by cord or bungee, are attached using the supplied machine screws
and lock nuts. - Cameras with a rear threaded hole, can be bolted directly to the Trail Camera T-Post Mount.
| Clamp at any height and face in any direction. |
Stealth Cam, Wildview, Tasco, and most other nylon strap equipped
cameras attach using the supplied metal strap, bolts and wing nuts; secure
at the appropriate holes labeled H.
Wildgame Innovations models S1.3, S2, S4 and IR4 attach with the
supplied machine screws and lock nuts; secure at slots A and holes B.
Wildgame Innovations model D6 and the Remington Sureshot attach with
the supplied machine screws and lock nuts; secure at slots A and holes D.
Wildgame Innovations Timber Eye and Remington Ghost: attach the
manufacture supplied Timber Eye/Ghost camera bracket to the T- post
mounting plate with the supplied bolts and wing nuts; secure at holes C.
Moultrie models D-40 and DGS series attach using the supplied machine
screws and lock nuts; secure at slots A and L.
cameras attach using the supplied metal strap, bolts and wing nuts; secure
at the appropriate holes labeled H.
Wildgame Innovations models S1.3, S2, S4 and IR4 attach with the
supplied machine screws and lock nuts; secure at slots A and holes B.
Wildgame Innovations model D6 and the Remington Sureshot attach with
the supplied machine screws and lock nuts; secure at slots A and holes D.
Wildgame Innovations Timber Eye and Remington Ghost: attach the
manufacture supplied Timber Eye/Ghost camera bracket to the T- post
mounting plate with the supplied bolts and wing nuts; secure at holes C.
Moultrie models D-40 and DGS series attach using the supplied machine
screws and lock nuts; secure at slots A and L.
| Attachment Legend |
Moultrie models D-55, D-55IR, I-35, I-45S, I-65S, M-45, and M-65 attach using the supplied metal strap,
bolts and wing nuts; secure at the appropriate holes labeled H.
Moultrie models M-40, I-40, M-60 and I-60 attach using the supplied metal strap, bolts and wing nuts;
secure at holes H3. Note: Remove and discard the rear mounted tilt adjusting thumbwheel as it causes
undue stress to camera body.
Cuddeback Capture, Bushnell Trophy Cam, Scoutguard 560, and DLC Covert II attach by passing the
camera’s rear strap loops through opening J. Then, working from the back side of the T-Post mounting
plate, slightly bow the supplied metal strap and pass it through the camera strap slots; secure metal strap
in place using the supplied bolts and wing nuts at holes H2.
Primos (most models) attach by using the supplied 1/4-20 bolts in the appropriate diagonally locate
threaded holes in the back of the camera; secure at "key holes" G. Bolts should only be snug, do not over
tighten, as plastic camera case could be damaged.
Attach the Trail Camera T-Post Mount to any suitably sized T-post, pipe, square tubing or angle iron
using the supplied U-bolts and wing nuts at holes K.
bolts and wing nuts; secure at the appropriate holes labeled H.
Moultrie models M-40, I-40, M-60 and I-60 attach using the supplied metal strap, bolts and wing nuts;
secure at holes H3. Note: Remove and discard the rear mounted tilt adjusting thumbwheel as it causes
undue stress to camera body.
Cuddeback Capture, Bushnell Trophy Cam, Scoutguard 560, and DLC Covert II attach by passing the
camera’s rear strap loops through opening J. Then, working from the back side of the T-Post mounting
plate, slightly bow the supplied metal strap and pass it through the camera strap slots; secure metal strap
in place using the supplied bolts and wing nuts at holes H2.
Primos (most models) attach by using the supplied 1/4-20 bolts in the appropriate diagonally locate
threaded holes in the back of the camera; secure at "key holes" G. Bolts should only be snug, do not over
tighten, as plastic camera case could be damaged.
Attach the Trail Camera T-Post Mount to any suitably sized T-post, pipe, square tubing or angle iron
using the supplied U-bolts and wing nuts at holes K.
We have strived to make the Trail Camera T-Post Mounting Bracket as universal as possible; it works very well with the
camera models pictured here as well as many other makes and models. The bracket can easily be drilled to adapt to
virtually any unforeseen application. Please contact us with any questions or suggestions: pat@murphymetalart.com
CAUTION: Over tightening camera attachment hardware may damage plastic camera components.
camera models pictured here as well as many other makes and models. The bracket can easily be drilled to adapt to
virtually any unforeseen application. Please contact us with any questions or suggestions: pat@murphymetalart.com
CAUTION: Over tightening camera attachment hardware may damage plastic camera components.
| FREE SHIPPING! $34.95 Please note: We do not sell outside of the continental United States of America. |
| Click on any image to enlarge |
| PM-AM Enterprises Inc., 2403 W. Arkansas, Pantego, TX 76013 pat@murphymetalart.com |
